cost of ghost immobiliser is the UK's most advanced aftermarket immobiliser that works with CAN buses. It's discreet and does not have LED indicators or key fobs and is concealed in the vehicle's wiring.
The user can also disable the system for a short period of time by using Transport Mode when renting out their car. This guide will walk you through the steps of installing an Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser protects your car against key hacking attacks, cloning and relay attacks. The system is directly connected to the ECU of your vehicle and protected by a pin code you select. It's inaccessible to thieves using diagnostic scanners or other modern methods, and it is unable to be disabled through circuit cuts.
The system is simple to use, however it's important to have professional installation to ensure a clean and secure connection with your vehicle's ECU. An approved installer from Thatcham can assist with the installation and programming of your Ghost system. They can also recommend a tracking or alarm system to complete the security package for your vehicle.
To prevent an accidental deployment of airbags or short circuits To avoid an accidental deployment of airbags or short circuits, the installer must remove your battery. Once the battery is disconnected, the installer can be able to work safely. Basic hand tools can be used to make precise connections. A multimeter can be used to test electrical values. Insulation tape and cable tie are crucial to ensure connections are secure and keep wiring tidy. The Ghost Immobiliser user's manual will give specific instructions that are specific to your particular model.
It is crucial to select a grounding location that is free of dirt or paint during installation. The installer must also make sure the immobiliser's H and CAN L wires are connected to the appropriate ports on your vehicle's ECU. Depending on the model, these wires may require soldering or plugged into. A top-quality connector is recommended to ensure a sturdy and secure connection.
Transport Mode can be activated by the customer once the installation is complete. This allows the vehicle to be utilized by valet parking companies or mechanics without needing to know the pin code. The customer has to press the icon for service on the dashboard five times over 2 seconds. After this is done the system will verify with 5 indication signals.
The Autowatch Ghost 2 is a highly efficient immobiliser that's TASSA verified and Thatcham approved. It's an excellent option for anyone who regularly rents out their cars through platforms such as Turo. An immobiliser can lower insurance costs since it reduces the likelihood of theft.
Getting Started
If you're looking for a solution that will safeguard your vehicle from theft it is best to go with an autowatch ghost immobiliser. It protects your vehicle from starting even when a criminal steals or copies the key. It's possible due to its advanced technology that prevents the engine from starting until the right PIN code has been entered.
The device is connected to the vehicle's bus system CAN and allows direct communication with the ECU. It uses existing buttons on the dashboard and steering wheel to create a unique sequence that only you know which makes it impossible for someone else to start your car. This is the best way to protect your pride and joy. It will not lose its value if you ever want to sell it.
Installing an immobiliser from Ghost is simple however, you must follow the directions to avoid electrical problems and malfunctions in the system. First, you must locate a power supply of 12V and a good grounding on the car's chassis. After that, you can begin connecting the wires for the immobiliser. Make use of high-quality connectors and soldering methods to create a secure connection. Make sure to shield the connections with heat shrink tubing or insulation tape, or other materials to prevent short circuits of electricity.
Once the wires have been connected, you can connect the battery and start the engine to determine whether the immobiliser works. Once everything is working properly, you can install it in a secure place under the dash or somewhere else in the vehicle. Be sure to cover it properly to stop any thief from taking advantage of it.
The Ghost 2 immobiliser has been TASSA (Tracker and Aftermarket Security System Association) which means it's a top-quality deterrent to car thieves. It is impervious to hacking and key cloning and cannot be disabled without the code. It is also simple to use and can be put into the service valet mode to ensure that your automobile will not be activated when you bring it in for maintenance or an MOT.
Wiring
The Ghost Immobiliser is a cutting-edge security system that's designed to stop theft of vehicles. It communicates with your vehicle's ECU and directly connects to its CAN bus. The Ghost Immobiliser does not interfere with your vehicle's factory settings, unlike other aftermarket systems which require the removal of circuit elements.
The system is also undetectable by thieves using diagnostic scanners. This is because the system doesn't send and receive radio frequency signals and it utilizes CAN data to communicate with your ECU. Furthermore, it doesn't require any modification to your vehicle's existing key fobs.
To utilize the Ghost Immobiliser, simply switch on the ignition of your car and enter your sequence for disarming (either one or two buttons). The indicator will flash two times to confirm that you've entered the correct code. After that, you are able to start your car and drive away in peace.
Once installed The Ghost Immobiliser can safeguard your vehicle from key cloning and hacking while preserving the value of your pride and joy. In Transport Mode, you can temporarily disable the Ghost Immobiliser when you need to give your car over for service or valet parking.
You'll require a constant power source (12V) in addition to a grounding point to complete the installation of a Ghost immobiliser. Ensure that these are both well-insulated and safe to touch. It is also recommended to use cable tie to secure and bundle the wires, since this will decrease the chance of theft by thieves. To avoid making mistakes, make sure to double-check these points and mark them using labels or tape. Examine every connection for signs that they're getting worn out. Be sure to ensure that all connections are in place, and are properly sealed. Finally, don't forget to test the Ghost Immobiliser after the installation is completed. This will make sure that the unit is working correctly and that all connections and insulation are safe. Be sure to correct any issues as soon as they arise.
Testing
The Autowatch Ghost immobiliser is a revolutionary vehicle security system that works seamlessly with your vehicle's ECU to stop unauthorized motor starting. Its cutting-edge technology protects your vehicle against key cloning and hacking along with other methods employed by thieves to steal cars. The Ghost works in conjunction with existing tracking and alarm systems to provide the most effective protection for your vehicle. The Ghost's unmatched features, combined with its subtle design makes it a preferred option for both car enthusiasts as well as security-conscious drivers.
It is essential to follow the procedures for installation to ensure a proper integration of Ghost Immobiliser. The best place to start is to refer to the wiring diagram of your vehicle, which will serve as a guideline to locate and connecting the required wires. You'll then need to identify the power and grounding sources. Once you've identified these you'll need to mark them so that they are easy to locate when installing. It is essential to use top-quality materials and tools. Basic hand tools will help you make precise connections. A multimeter can verify electrical values, and also ensure safety. Cable ties and insulation tape can help keep connections neat and tidy. Additionally, a user's manual will provide specific guidance specific to your Ghost model.
Before beginning the installation, it's important to test the system by entering the PIN code, then starting the vehicle. This will ensure that the immobiliser functions as intended and prevent unauthorised vehicle starts. This procedure should be carried out regularly as part of your routine vehicle inspections in order to ensure the system is always functioning properly.
After the installation is completed, you can drive your vehicle with confidence. The Ghost will protect your vehicle from thieves who might steal your car. It will ensure that no one will escape with your car if they do not have the correct PIN code. The Ghost can be used in conjunction with an approved Thatcham tracker, which detects attempts at theft or tampering. This lets you locate your car if it's stolen.
The Ghost is compatible with a wide variety of automobiles, including those from the majority of major manufacturers. Monty's Locksmith can assist you in securing your vehicle with this cutting edge device. Contact us today to find out more about our services and installation options. We are a TASSA registered installer, a certificate that ensures that we adhere to strict standards in the installation of our products. This ensures customers insurance companies, customers, and law enforcement agencies that installations are performed safely and correctly.