Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser designed for CAN buses. It's discreet, doesn't use key fobs or LED indicators and is concealed within the vehicle's wiring.
It also permits the user to turn off the system temporarily by using Transport Mode to use it when they are renting their vehicle. This guide will take you through the installation of an Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser protects your car against key hacking attacks, cloning attacks and relay attacks. The system is directly connected to the ECU of your car and secured by a PIN code you select. It's undetectable to thieves using diagnostic scanners or other modern methods, and is not able to be disabled through circuit cuts.
The system is simple to use, but it's important to have professional installation to ensure a secure and secure connection to your vehicle's ECU. An approved installer from Thatcham can assist with the installation and programming of your Ghost system. They can also suggest an alarm or tracking system to complete the protection package for your vehicle.
First, the installer needs to disconnect your battery to prevent the possibility of airbag deployment and short circuits. After this is completed the installer is able to safely begin work. Basic hand tools can be used to make precise connections. A multimeter is useful to check electrical values. Cable tie and insulation tape are vital to secure connections and keep wiring neat. In addition, the user's manual gives specific guidelines that are tailored to your Ghost Immobiliser model.
During the installation, it is essential to choose a grounding point that's free of paint and debris. The installer should also make sure the immobiliser's CAN H and CAN L wires are connected to the correct ports on the vehicle's ECU. Based on the model, these wires might require soldering or plugged in. Using a top-quality connector is recommended to ensure a long-lasting and secure connection.
Once the installation is complete, the customer can activate after the installation is complete, the customer can activate Transport Mode. This allows valet parking or mechanics to use the vehicle without knowing the pin code. To accomplish this, the customer has to press the button for service on the dashboard 5 times within 2 seconds. The system will confirm this by displaying 5 indicators.
The Autowatch Ghost 2 is a highly effective immobiliser that's TASSA verified and Thatcham approved. It's a great choice for those who rent out their vehicles regularly on platforms such as Turo. An immobiliser can cut down on the cost of insurance, as it lowers the chance of theft.
Getting Started
You won't have a problem with an autowatch immobiliser if you want to protect your car from theft. It protects your vehicle from being started even when a criminal steals or copies the key. This is due to its advanced technology that is designed to stop the engine from running unless the correct PIN code is entered.
The device connects to the CAN bus network of your vehicle which allows it to communicate with the ECU directly. It uses buttons that are already present on the dashboard and the steering wheel to create a unique sequence only you can identify which makes it impossible for someone else to start your vehicle. This is the most secure security system that protects your car's pride and joy and will ensure its value when you want to sell it in the future.
Installing a Ghost immobiliser is easy however, you must follow the directions to avoid electrical problems and malfunctions of the system. First, you need to find and locate a permanent 12V power source as well as a good grounding point on the chassis of your vehicle. Then, you can begin connecting the wires to the immobiliser. Make sure you use top-quality connectors and soldering methods to ensure a secure connection. Insulate the connections using heat shrink tubing, insulation tape or other materials to avoid short circuits of electricity.
Once the wires are connected, you can connect the battery and turn on the engine to test the immobiliser's function. When everything is functioning correctly you can place it in a safe location beneath the dash or anywhere else in the vehicle. Make sure to cover it well to ensure that thieves cannot get it into a compromising position.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) verified This means it complies with the highest standards of security and is a fantastic protection against car thieves. It is resistant to key cloning and hacking and cannot be disabled without the code. It is also simple to use and can be set into a service valet mode so that your vehicle will not be activated when you take it in for maintenance or an MOT.
Wiring
The Ghost Immobiliser is a cutting-edge security system that's designed to prevent vehicle theft. It communicates with your vehicle's ECU and connects directly to its CAN bus. In contrast to other aftermarket systems that require the removal of circuit components, the Ghost Immobiliser doesn't interfere with your vehicle's factory settings.
It's also completely undetectable to thieves using diagnostic scanners. This is due to the fact that it doesn't send and receive radio frequency signals, and it utilizes CAN data to communicate with your ECU. In addition, it doesn't need any modifications to your vehicle's existing key fobs.
To utilize the Ghost Immobiliser, simply switch on the ignition in your car and then enter the sequence to disarm (either one or two buttons). The indicator will flash two times to confirm that you've entered the correct code. After this, you can start your car and drive away safely.
Once installed, the Ghost Immobiliser protects your car against key cloning or hacking while also protecting its value. In Transport Mode, you can temporarily disable the Ghost Immobiliser when you need to give your car to service or valet park.
You'll need a constant power source (12V) and a grounding point to complete the installation of the Ghost immobiliser. Ensure that these are both well-insulated and safe to touch. Cable ties are also suggested for bundling and securing the wires. This will reduce the chance of theft by thieves. Be sure to check the exact location of these points to avoid making mistakes, and mark them with an adhesive or label. Examine all connections for signs they're wearing out. Make autowatch ghost 2 immobiliser that all connections are in place and properly insulated. Don't forget to test the Ghost Immobiliser after the installation is complete. This will confirm that the unit functions properly and that all connections and insulation are secure. If you encounter any issues, be sure to address them immediately.
Testing
The Autowatch Ghost Immobiliser is a cutting-edge car security system that seamlessly into your car's ECU to prevent unauthorised engine start. Its innovative technology safeguards your vehicle against key cloning and hacking along with other methods commonly used by thieves to steal cars. The Ghost works in conjunction with existing tracking and alarm systems to provide the best security for your vehicle. The Ghost's unique features, combined with its discreet design makes it a sought-after choice for drivers who love cars and security-conscious drivers.
It is important to follow the procedures for installation to ensure a proper integration of Ghost Immobiliser. A good starting point is to consult the wiring diagram of your vehicle that serves as a roadmap for locating and connecting the required wires. You'll need to determine the grounding and power sources. Once you've found them then you'll need to mark them so that they're easily identifiable when installing. Finally, it's important to use top-quality tools and materials. Hand tools are essential to assist you in making precise connections. A multimeter will verify electrical values, and ensure security. Insulation tape and cable tie will ensure that all connections are tidy. Also, a user's guide will provide specific instructions specifically tailored to your Ghost model.
Before proceeding with the installation it is essential to test the system by entering the PIN code and then starting the vehicle. This will ensure that the immobiliser functions as intended and will stop vehicle starts that are not authorized. It is recommended that you perform this procedure regularly as part of your regular vehicle inspections to ensure that the system is always functioning properly.
After the installation is completed, you can drive your vehicle with confidence. The Ghost will safeguard your car from would-be car thieves. It will ensure that no one can drive away with your vehicle without having the correct PIN code. The Ghost can be paired with an approved Thatcham tracker that identifies any attempts to steal or tamper with. This allows you to locate your car if it's stolen.
The Ghost can be used on a wide range of vehicles and is compatible with most major brands. Monty's Locksmith can assist you in securing your vehicle with this cutting edge device. Contact autowatch ghost 2 immobiliser to find out more about our service and installation options. We are a TASSA registered installer, a certificate that guarantees we follow strict standards for the installation of our products. This assures insurance companies, customers, and law enforcement that installations are done safely and correctly.