Ghost Immobiliser Fitting
Protect your vehicle against key theft, cloning and hacking by using the first aftermarket CAN-Immobiliser. With cost of ghost immobiliser added option to connect to an Ghost app and GPS tracking system that will notify you via phone in the event that your vehicle is damaged with or stolen.
The installation of a Ghost immobiliser can be completed by a certified technician. Having the right tools, insulation tape, and heat shrink tubing is essential.
Getting Started
Unlike physical theft protection devices like wheel locks and car alarms, ghost immobilisers protect your vehicle without the need for LEDs or key fobs. They are directly connected to the ECU CAN data network, and can only be activated after entering a PIN. ghost 11 immobiliser provides a higher level of protection against key hacking, ECU swapping and cloning.
Installing a ghost immobiliser Birmingham requires a high degree of agility and accuracy. It can be a bit like walking through the minefield. A single mistake could cause irreparable damage to the circuits of the electrical system of your vehicle. It is essential to comprehend the procedure for installing and prepare your vehicle correctly.
The first step is to prepare the vehicle by taking out interior panels to make space for the immobiliser unit. Once you have found the perfect place to hide it then use cable ties to fix it. Then, tidy your wiring by tying loose wires down and using insulation tape to cover any exposed connections. This will minimize the risk of short circuits that are not intended to be there while also improving the aesthetics and decreasing the likelihood of tampering by thieves.
Then, locate the source of constant 12V power as well as a grounding location for the ghost immobiliser. Once you've identified these connections, test the power cables using a multimeter, to ensure they're delivering the same voltage. Connect the CAN H & the CAN L wires from the immobiliser with the grounding and power points.
After you've made all the connections required, it's important to double-check the connections and examine the immobiliser for signs of corrosion or damage. It is also important to test the system to make sure it is working properly by entering a pin code and starting the engine. This should be a regular part of your routine, as it will allow you to spot any intermittent problems early. Regular testing can help extend the life of your device and ensure it is performing at its best.
Preparing the Vehicle
Installing a Ghost immobiliser requires the right expertise and tools. A wiring diagram is crucial to identify the right wires, making accurate connections and ensuring security. A multimeter can be used to check the electrical properties and ensure security. Insulation tape and cable ties can be used to guard connections from being tampered with and to ensure they are secured. Finally, a user guide will provide specific directions tailored to your Ghost Immobiliser model.
Once installed, a ghost immobiliser can prevent unauthorised engine start by requiring the driver to enter a unique PIN sequence using buttons on the steering wheel or centre console. This can be accomplished manually or remotely using an app for mobile phones, and the code can be modified by the vehicle's owner at any time. The device is also silent and is inaccessible to thieves because it does not emit radio frequencies.
Ghost immobilisers are directly connected to the CAN bus of the vehicle, a network that communicates with the electronic control units (ECUs) of the vehicle. It intercepts the signals transmitted by ECUs, and blocks the engine when a false signal is detected. The system is tamperproof and weatherproof, but it does not have LED indicators or key fobs to attract the attention of thieves.
It can be positioned behind or in a more obscure area to ensure that it isn't visible to thieves, and does not interfere with vehicle performance. It can be placed in a small container, so that it is less likely to be spotted by unscrupulous salespeople during a test-drive.
Its stealthy operation and integration with the vehicle's CAN bus system makes it a powerful deterrent to modern methods of theft, like key cloning and signal relay attacks. The system can be paired with other security measures to create a powerful barrier that can deter even the most obstinate thieves. This is the reason why more insurance companies are now recommending or even requiring ghost immobilisers be installed, as it can significantly reduce the cost of insurance.
Making Connections
Unlike traditional security systems that can be heard by thieves, ghost immobilisers work silently to stop them from knowing that your vehicle has been switched on. They also block high-tech methods of stealing vehicles, like OBD hacking. They can also be put in without causing permanent marks in your vehicle making them a good option for those who are planning to sell their vehicle in the near future.
The Autowatch Ghost 2 CANbus immobiliser is one of the latest and most reliable methods to stop car theft. It shuts down your engine by using the CAN data network and generates a unique PIN code that is difficult for criminals to guess. It can be used in a wide range of automobiles, and it can work with a variety of features already installed like car alarms, steering wheel locks, GPS trackers and door lock bypass.
If you opt to use an Ghost immobiliser for your vehicle, make sure you refer to the wiring diagram to determine the wires that connect. Verify the location of these wires to ensure their accuracy and mark them using labels or tape to aid in keeping on track of them. autowatch ghost immobiliser is also necessary to locate a source of continuous power (12V) and a grounding point to the system. Once these are in place, you are able to begin to make the connections needed to complete the installation.
The ghost immobiliser will not allow your vehicle to start unless a pin code is entered through the buttons on the dashboard or steering wheel. This will stop ECU hacking keys cloning, hacking, and other methods of theft from vehicles. In addition, it can be paired with other approved by Thatcham security devices, like alarms and tyre clamps to give your car an even greater level of protection.
As the UK automotive industry continues to grow so do the options available for protecting your vehicle. There are a myriad of ways for thieves to get into your car and take it, so it's important to do all you can to prevent it from being taken away. This is why ghost immobilisers are very popular among responsible car owners.
Testing the System
The Ghost Immobiliser uses a CAN data network to communicate with the vehicle's ECU, preventing the engine from starting until a specific PIN code is entered. This makes it extremely difficult for thieves to copy your key fob and then start your vehicle, and more difficult to disable the system through hacking into its electronic components.
Ghost Immobilisers can also be used in conjunction with GPS tracking devices to help locate your vehicle in the event that it is stolen. This feature is not commonly available in aftermarket security products, but it is an excellent way to improve your vehicle's security and provide you with peace of mind.
In addition to providing enhanced security and security, the Ghost-II immobiliser also provides a comfortable user experience by eliminating the requirement for additional key fobs or devices. It has a simple and intuitive PIN code entry system that integrates seamlessly into your everyday routine. In addition, it offers options for deactivation and features that allow you to temporarily disable the immobiliser valet parking and servicing.
Before you begin the installation process, familiarize yourself with the vehicle's wiring and prepare the necessary tools. A basic set of tools can enable you to make precise connections. A multimeter can be used to check electrical values. Insulation tape and heat shrink tubing are also crucial for securing connections from short circuits, and cable tie is a great way to secure the wiring in place. Additionally, it is essential to be in a well-lit space and wear the appropriate safety equipment when working with tools and electrical components.
After you've completed the installation, you must test the Ghost immobiliser to make sure that it's working properly. You should first try to start the vehicle without entering the PIN. If this fails then you'll need to test again and examine the connections more carefully.
In contrast to other security systems, the Ghost Immobiliser is a covert device that cannot be detected by thieves and is far more effective than conventional physical deterrents, such as wheel clamps or steering locks. It is TASSA recognized and approved by some insurance companies, making it an investment that's cost-effective and will provide you with peace of mind you need.